Advanced Modeling of Friction Stir Welding – Improved Material Model for Aluminum Alloys and Modeling of Different Materials with Different Properties by Using the Level Set Method
Wilhelm Gronbach GmbH, Wasserburg a. Inn, Germany
Friction Stir Welding (FSW) has gained much importance throughout the last years. Beside comprehensive experimental work that has been carried out, the simulation of the welding zone is of major interest. Due to the high strains observed within the welding zone, the Eulerian (CFD) approach seems to be the most promising for the prediction of flow around the FSW tool. However, the CFD ...
H. Schmidt[1,2], and J. Hattel
Technical University of Denmark, Kgs. Lyngby, Denmark
HBS Engineering, Frederiksberg, Denmark
Two friction stir welding models are presented – a global thermal model using the temperature dependent heat source and a local material flow and heat generation model allowing for detailed investigation of different contact conditions. The two models are coupled into a larger local-global model. The flow model includes frictional dissipation from the contact between the work piece and the ...
E. Le Guen, R. Fabbro, F. Coste, M. Carin, and P. Le Masson
LALP (CNRS)/GIP GERAILP, Arcueil, France
LIMATB, Université de Bretagne Sud, Lorient, France
Hybrid laser-MIG arc welding has very interesting advantages compared to laser welding or arc welding used separately. It is known that improvement of productivity results in higher welding speeds, thicker welded materials, joint fit-up allowance, better stability of molten pool, and improvement of joint metallurgical quality. In order to use these techniques efficiently in industrial production, ...
D. Grondin, J. Deseure, A. Brisse, M. Zahid, and P. Ozil
Laboratoire d’Electrochimie et de Physico-chimie des Matériaux et des Interfaces (LEPMI), Saint Martin d’Hères, France
European Institute for Energy Research (EIFER), Karlsruhe, Germany
Based on solid oxide fuel cell (SOFC) technology, the solid oxide electrolysis cell (SOEC) offers an interesting solution for mass hydrogen production. This study proposes a multiphysics model to predict the SOEC behavior. A global approach and several electrochemical kinetic equations were used for modeling. The simulated results demonstrated that a Butler-Volmer’s equation including ...
Liquid Metal Metallurgy and Solidification department
Ugitech’s Research Center, Ugine, France
Dr. Christian Deville-Cavellin is a Research Engineer at Ugitech's Research Center, since 1995. Ugitech, member of the Schmoltz & Bickenbach group, is a stainless steel, long products producer. C. Deville-Cavellin is responsible for all research topics related to liquid metal metallurgy and solidification. He also keeps an expert role in machinability, within one of the french public ...
Multiphysics Simulation of Thermoelectric Systems - Modeling of Peltier-Cooling and Thermoelectric Generation
Fraunhofer-Institute for Physical Measurement-Techniques (IPM), Freiburg, Germany
Electro-thermal interaction is commonly considered only as a matter of joule heating. In addition, the Seebeck-, Peltier- and Thompson-Effects are significant in materials with high thermoelectric figure of merit Z. These thermoelectric materials have a high Seebeck-coefficient α, a good electric conductivity σ, and a poor thermal conductivity λ. They have widespread areas of ...
C. Gavrila, A. Ghiaus, and I. Gruia
Technical University of Civil Engineering Bucharest, Faculty of Building Services, Bucharest, Romania
University of Bucharest, Faculty of Physics, Bucharest, Romania
A dynamic mathematical model, based on physical and transport properties and mass and energy balances, was developed for the simulation of unsteady convective drying of agricultural products (fruits and vegetables) in static bed conditions. The model utilizes water sorption isotherm equations and the change in solid density due to the shrinkage phenomenon. The aim of this article is to describe ...
Prediction and Optimization of Surface-Enhanced Raman Scattering Geometries using COMSOL Multiphysics
I. Knorr, K. Christou, J. Meinertz, A. Selle, J. Ihlemann, and G. Marowsky
Laser-Laboratorium Göttingen e.V., Germany
Raman spectroscopy is a commonly used tool in biodiagnostics and sensor technology. Surface-enhanced Raman scattering provides high signal enhancements especially at nanostructured metallic surfaces. In this paper the electromagnetic Raman enhancement from different metallic nanostructures - including gold coated gratings, spherical and hemispherical particles - is calculated by using the finite ...
Simulation of a Diesel Oxidation Catalyst Used in a NOx Storage and Reduction system for Heavy Duty Trucks
C. Odenbrand, and E. Senar Serra
Department of Chemical Engineering, Lund University, Lund, Sweden
This work concerns the performance of an oxidation catalyst used in a NOx storage and reduction system. The oxidation of NO is the main objective of this study, where the presence of CO and propene has also been taken into account. Experimental data has been determined on a monolithic oxidation catalyst mounted after a heavy duty diesel engine in a rig. The conversion of hydrocarbons is predicted ...
G. Petrone, G. Cammarata, S. Caggia, and M. Anastasi
Department of Industrial and Mechanical Engineering, University of Catania, Catania, Italy
Engineering Maintenance - ISAB Energy Services, Priolo Gargallo, Italy
In this study, COMSOL Multiphysics is applied in order to simulate reacting flows for duct burner systems arranged in the post-firing section of a Heat Recovery Steam Generator of a combined cycle power plant. Two- and three-dimensional simulations are carried out in order to investigate on operative conditions mainly responsible of duct burners overheating. The results are obtained for several ...