Menu

Discussion Forum

New Discussion
Filter

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Modelling using darcy law for multiphase flow in porous media

Posted Feb 20, 2019, 7:18 a.m. EST Fluid & Heat, General, Heat Transfer Version 5.4 1 Reply

Swati Gupta
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

I am trying to model a system having 2 phases. I am using physics Multiphase Transport in porous media, which by default adds two physics - Phase Transport in Porous Media and Darcy Law interface coupled by multiphysics. I want to solve pressure for both two phases, water and gas which gives velocities for both water and gas. But this interface only solves for one pressurre and only one velocity. But in Phase Transport in Porous Media solves for 2 saturation, one gas and one water. How can I do so?

1 Reply Last Post Mar 7, 2019, 4:17 a.m. EST
Tycho van Noorden COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 6 years ago Mar 7, 2019, 4:17 a.m. EST

Dear Swati Gupta,

If you use the Multiphase Flow in Porous Media multiphysics interface, which couples a Darcy's Law interface and a Phase Transport in Porous Media interface, the Darcy's Law interface indeed computes for the pressure of only one phase. However, from this pressure of one phase, the Phase Transport in Porous Media interface computes the pressures of both phases, using a capillary pressure function. From these two pressures, the velocities for both phases are then computed. These pressures are usually called phtr.p_s1 and phtr.p_s2, and the velocities are usually called (phtr.ux_s1,phtr.uy_s1,phtr.uz_s1) and (phtr.ux_s2,phtr.uy_s2,phtr.uz_s2). These variables can be used for plotting and are available in the plot menu. More details can be found in the Subsurface Flow Module User's Guide.

Another approach for two-phase flow in a porous medium, can be found in the following example model: https://www.comsol.nl/model/two-phase-flow-experiment-499 where two Darcy's Law interface are used.

In principle the two approaches (two Darcy's Law interfaces or the Multiphase Flow in Porous Media multiphysics interface) should give the same results.

Best regards, Tycho van Noorden, COMSOL

Dear Swati Gupta, If you use the Multiphase Flow in Porous Media multiphysics interface, which couples a Darcy's Law interface and a Phase Transport in Porous Media interface, the Darcy's Law interface indeed computes for the pressure of only one phase. However, from this pressure of one phase, the Phase Transport in Porous Media interface computes the pressures of both phases, using a capillary pressure function. From these two pressures, the velocities for both phases are then computed. These pressures are usually called phtr.p_s1 and phtr.p_s2, and the velocities are usually called (phtr.ux_s1,phtr.uy_s1,phtr.uz_s1) and (phtr.ux_s2,phtr.uy_s2,phtr.uz_s2). These variables can be used for plotting and are available in the plot menu. More details can be found in the *Subsurface Flow Module User's Guide*. Another approach for two-phase flow in a porous medium, can be found in the following example model: [https://www.comsol.nl/model/two-phase-flow-experiment-499](https://www.comsol.nl/model/two-phase-flow-experiment-499) where two Darcy's Law interface are used. In principle the two approaches (two Darcy's Law interfaces or the Multiphase Flow in Porous Media multiphysics interface) should give the same results. Best regards, Tycho van Noorden, COMSOL

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content