Finding the Best Coal Arrangement for Even Heat in a Grill
Magnus Ringh January 25, 2017
There is always time to think about how to improve your grilling skills. In this blog post, we show how to use the COMSOL Multiphysics® software to determine the best way to arrange the coals or briquettes in a charcoal grill for even heat and to avoid hot spots. Even heat is required when making a grilled pizza, for example.
Heat Transfer and Charcoal Grilling
When using a grill, heat transfer to the food occurs primarily through thermal radiation. This means that, in a common charcoal kettle grill, heat reaches the food through direct radiation from below as well as through reflection from the kettle walls. Depending on the food that you are grilling, the desired heat distribution may vary.
Pizza on a grill. (This photo is from our pizza grilling experiment — watch the video here.)
For a steak, for example, you may want to use a so-called two-level fire, where you pile most or all of the coals on one side of the grill. You can sear the steak on this hot side and then finish cooking it on the other side, where the heat is gentler. If you put the lid on the grill, it acts more like a convection oven, which is a good method for larger roasts and whole birds. Such slow cooking is usually referred to as barbecuing rather than grilling.
Other cases, such as when you want to make a grilled pizza, require heat that is intense but also evenly distributed without hot spots that might burn the food. You would think that an even, single-layer fire would be the best way to achieve even heat, but practical experiments and simulation show that there is an optimal, and perhaps unexpected, coal arrangement.
A Ring of Fire
The best method for even grilling, as reported in a recent Cook’s Illustrated article, is to shape the coals into a ring, leaving the center of the grill empty. Though it sounds counterintuitive, a fire with the coals spread across the grill will not provide an even heat at the grill grate. This happens because the food is not just subjected to heat from below. In addition, the curved kettle walls reflect the heat inward, creating a hot spot at the center of the grill.
Heat from a grill with a ring of coals (left) and evenly distributed coals (right).
Let’s see how, using COMSOL Multiphysics, we can compare different coal arrangements and their effect on heating in a grill and thereby confirm (or not) what is indicated as the best arrangement for even heat.
Simulating Surface-to-Surface Radiation in a Grill
In COMSOL Multiphysics, we can use the Heat Transfer with Surface-to-Surface Radiation interface, available in the Heat Transfer Module, to test how different coal placements affect the grill’s temperature, including:
- Coals in the center
- Coals in a ring at the perimeter
- Coals everywhere
The objective of the simulation is to check, for these three cases, the average temperature and the difference between the highest temperature and the lowest temperature. If the temperature difference is smaller, then the temperature is more even, which is what we want to achieve for the best results.
In our COMSOL® model, we make use of the symmetry of a conventional kettle grill and model it using an axisymmetric 2D geometry. To account for the three coal configurations, we add parameters for the distance from the center, the number of coals, and the distance between each coal. Then, a parametric sweep is set up so that a single study provides the simulation results for all three cases. Heat transfer by natural convection is neglected as heat transfer by radiation is supposed to dominate.
The simulation uses material properties for three materials:
- Air, which is the large domain surrounding the coals inside the kettle
- Steel, for the kettle walls and grate
- Coals, where data for the thermal conductivity, density, and heat capacity are taken from Heat Transfer (Wiley) by A. Bejan; the values are approximate (and for a stationary study without convection, the heat capacity and density are not needed)
For the domains, air is treated as a fluid and the steel domains and coals as solids. In addition, each coal acts as a heat source, with a heat rate defined using a power of 3 kW.
For the boundary conditions, all boundaries are considered as diffuse surfaces that reflect radiative intensity uniformly in all directions. The initial temperature and the ambient temperature are set to 293.15 K (20°C). The exception is the symmetry boundary, which uses a predefined axial symmetry condition.
To increase the accuracy in the model using surface-to-surface radiation, boundary layer meshing is added for the coal boundaries.
To compute the stationary study for all three cases, a Parametric Sweep node is set up to sweep over three specified combinations of parameter values corresponding to the three coal arrangements. The full parametric sweep to compute the temperature in the kettle grill only takes a minute or two on a normal workstation.
To postprocess the results from an axisymmetric simulation, we can use Revolution 2D data sets, which take an axisymmetric Solution data set as their input and revolve it into a 3D solution. The following plot shows a revolved solution for the simulation case with coals in a ring.
The kettle temperature for the case where the coals are placed in a ring. The axisymmetric solution is revolved 225 degrees.
Which Coal Arrangement Provides the Most Even Heat?
To get the numerical values that provide the quantitative results from these simulations, we use a Global Evaluation node to evaluate the temperature difference and the average temperature for the solution at the grill grate. For the evaluation, we use Maximum, Minimum, and Average operators, all defined on the top boundary (the grate) only. The evaluation of the temperature values gives the following results (rounded values in K):
|Coal Configuration||Temperature Difference||Average Temperature|
|Coals in the center||166||501|
|Coals in a ring||92||502|
There is a much smaller temperature variation with the coals arranged in a ring, whereas the average temperature is almost the same in all three cases. So the simulations confirm what experiments have indicated: Arrange the coals in a ring for the most even heat in a conventional kettle grill.
The following plots, using a Solution data set with a Selection subnode restricting the data to the grate only, show the temperature at the grate for the three cases:
Plots of the grate temperature for coals in the center (left), everywhere (center), and in a ring (right).
In this blog post, we outline an easy-to-understand example of how simulation can help make an informed decision on a design — even in everyday life. By simulating surface-to-surface radiation in COMSOL Multiphysics, we can clearly see that coals arranged in a ring around the perimeter of the grill provide the most even heat. Now, let’s get ready for grilling season!
- Explore further uses of simulation for food applications on the COMSOL Blog: